Build your own effects pedal

Build your own effects pedal

Here’s a short DIY tutorial to show that you can easily build your own effects pedal

I’ll try to explain the main steps you need to build your own effects pedal.

For this demonstration we’ll build a Tube Screamer clone (Ibanez TS808), because it’s a hugely popular circuit, fairly simple to build, and a great overdrive pedal on top of that 🙂

We won’t build it on a printed circuit board, because making your own PCBs takes a fair amount of practice and equipment. So, even though this approach has a few drawbacks (sometimes unreliable connections), we’ll use a veroboard like this one instead, which is much easier to find:

veroboard for building an effects pedal
a veroboard for building your own effects pedal

If you want cleaner, easier builds, you can buy printed circuit boards ready to take the components from tonepad.com. Lots of circuits are available (Phase 90, Big Muff, MXR Distortion…) and the PCBs are good quality.

1 – Step one: find the right schematic

Plenty of websites offer layouts to clone many commercial pedals or build completely original circuits. But if you don’t want to search every corner of the web for the Holy Grail, head to one of these two sites:

http://www.sabrotone.com/

http://tagboardeffects.blogspot.com/

Here is the layout we’ll use for our Tube Screamer:

Tube Screamer vero layout from http://tagboardeffects.blogspot.com/
Tube Screamer vero

This is the TS808 circuit with a switch to change the type of clipping components used for the overdrive (regular diode or LED).

2 – Find and buy the components

There are many websites where you can buy components, but personally I usually find everything I need at Taydaelectronics, and if I can’t find a part there, I simply look for it on eBay.

Next, unless you’ve studied electronics, finding the right part numbers will probably be fairly tricky. But with a bit of perseverance you should manage.

A few tips:

  • unless stated otherwise, use 1/4 watt resistors.
  • you can choose metal film resistors (not mandatory, but they’re supposed to be better quality and the price difference is minimal).
  • convert capacitor values if you can’t find the right reference: http://www.justradios.com/uFnFpF.html
  • as for capacitor voltage, since size is the main criterion, choose whichever will fit most easily, as long as they’re rated at least 18 volts (unless the schematic specifies otherwise).
  • use metal film capacitors if they’re available.
  • remember to buy wire (AWG 22 Hook-Up Wire 1FT (30cm) Solid) and heat-shrink tubing.

3 – The build

start by cutting the tracks on the veroboard according to the layout.

For that, I haven’t found anything more practical than a small drill bit.

Careful: you need to cut the tracks and place the jumpers keeping in mind that the components go on the side of the veroboard without copper tracks (so mirrored relative to the layout if you’re looking at the copper tracks)!!

Also check that there’s no continuity left between the cut tracks, because it’s very common for a tiny bit of copper to remain, and in my opinion it’s the main cause of a faulty build. Personally, I go over each cut with a utility knife blade after cutting the tracks with the drill bit.

Then make and solder the jumpers, and place and solder the components. Be careful not to stay on the components too long while melting the solder. Also be careful not to get any on the neighboring tracks.

Tube Screamer - DIY vero - track side view

 

DIY Tube Screamer - vero
DIY Tube Screamer – component side

All that’s left is to solder the pots, jacks, 9-volt power jack and footswitch to the veroboard.

Here’s how the potentiometer legs are numbered:

potentiometer legs number
Potentiometer leg numbering

 

As for the enclosure, this build should fit in a 125B, but if you’re a beginner, go for a 1590BB to make things easier.

More info on the different Hammond aluminum enclosure sizes here: http://www.mammothelectronics.com/aluminum-enclosures-s/22.htm

And here’s the result:

Finished DIY Tube Screamer overdrive pedal: aluminum enclosure and red knobs

 

Sound-wise, I’ve never tried a real Tube Screamer, but I can tell you this DIY Tube Screamer sounds absolutely great. Every pedal I’ve built works very well and can be used without any problems.

Go for it!

Be the first to comment

Leave a Reply